濟南感應門安裝注意事項：

　　Ji 'nan induction door installation precautions:

　　1.濟南感應門的皮帶張緊輪模塊：皮帶掛在皮帶張緊輪上，該模塊配備了調理皮帶張力的組織

　　The belt tensioning wheel module of Ji 'nan induction door: the belt is hung on the belt tensioning wheel, and the module is equipped with the organization of regulating the belt tension

　　2.主動門傳動機箱導軌：用高強度、耐磨鋁材制成

　　Guide rail of driving door chassis: made of high-strength and wear-resistant aluminum

　　3.感應門裝置時吊件模塊：用于門體吊掛，本模塊上裝有導輪，可以在主動門機箱導軌上挪動

　　Suspension module for induction door device: used for door body hanging, the module is equipped with a guide wheel, which can be moved on the guide rail of the active door chassis.

　　4.止位器：避免吊夾在導軌上挪動時，移出導軌

　　Stopper: avoid moving the hanging clip out of the guide rail when moving on the guide rail.

　　5.操控器模塊：接納傳感器或許其它信號開關的檢測信號，驅動馬達，操控門體裝置適宜的方法運動

　　Controller module: accept the detection signal of sensor or other signal switch, drive the motor, and control the door body device in the appropriate way.

　　6.電動機模塊：選用體積小、功率大的直流無碳刷馬達，合作傳動效率高、噪音小的高速齒輪箱體系減速，然后驅動皮帶

　　Motor module: the dc brushless motor with small volume and large power is selected, and the high-speed gearbox system with high efficiency and low noise is used to slow down and drive the belt.

　　7.皮帶模塊：將電動機模塊的轉變變?yōu)橥鶑?fù)運動。選用特別資料工藝的齒形皮帶，彈性性小，不受溫度影響，傳遞效率高，所以不必因皮帶彈性做調整

　　Belt module: change the motor module into reciprocating motion. The toothed belt with special data technology has small elasticity, is not affected by temperature and high transmission efficiency, so there is no need to adjust the belt elasticity.

　　濟南感應門安裝步驟教程：

　　Ji 'nan induction door installation steps tutorial:

　　一、軌道的固定：保證軌道水平、牢固、穩定。

　　First, the fixed track: to ensure the level, firm and stable track.

　　二、玻璃吊架、滑輪安裝：

　　Ii. Installation of glass hanger and pulley:

　　1、玻璃吊夾兩側均勻安裝，并且保證螺絲擰緊。

　　Evenly install both sides of the glass lifting clip, and ensure that the screws are tightened.

　　2、掛上吊輪，裝好門扇皮帶、擰緊尾輪螺絲 繃緊皮帶。

　　Hang the hanging wheel, install the door fan belt and tighten the tail wheel screw to tighten the belt.

　　3、將門扇掛入軌道，來回滑動檢測是否順暢。

　　Hang the door fan into the track and slide back and forth to check whether it is smooth.

　　三、動力裝置安裝：

　　Iii. Power device installation:

　　1、固定好馬達、控制器、主尾輪皮帶。

　　Fix the motor, controller and main tail wheel belt.

　　2、將重疊門扇均勻分布，確定開啟位置將皮帶用配套卡口固定牢固。

　　the overlapping door fan evenly distributed, determine the opening position of the belt with supporting bayonet fixed firmly.

　　3、裝好感應器、防撞條、啟動電源調試。

　　Install inductor, anti-collision bar, and start power debugging.